Cable Clamps

• Self-Adhesive Tie Mount
• UL approved material NYLON 66, 94V-2 (Backed with adhesive tape) .
• SELF-ADHESIVE TIE MOUNTS is designed to support light weigh wire bundles when properly applied on any clean, smooth, grease free surface. For heavy support mounting hole is provided for screws.
• To apply, simply peel off backing paper and apply mount to surface after that, cable ties can be inserted to secure wire bundles.
• Available in Black & White.

We offer a wide range of copper and aluminium cable lugs, connectors, and terminals.

• Tubular insulated and heavy-duty lugs for XLPE and medium/high-voltage cables
• Copper and aluminium connectors and terminal ends with solid barriers
• Compression sleeves and full-tension joints for reliable connections
• Medium-voltage straight splices for efficient cable joining
• Copper end-sealing ferrules and plastic end sleeves
• Solder-type weak-back ferrules and tinned screw sleeves
• Punched copper lugs with bolted connections

Ring Terminal

Terminal Material – Copper

Insulation Material – Vinyl

Spade(Fork) Terminals

Terminal Material – Copper

Insulation Material – Vinyl

Cord End Terminals

Terminal Material – Copper

Insulation Material – Nylon

Edging Grommet

• PE Natural Material.
• Cut length optionally to fit your chassis edging protection or other application for smoothing edges.
• Protect wires, cables and chassis insulation

Grommet (Open/Closed)

• Low cost protection for wires and cables passing through metal panels
• Quick and easy to install
• Closed hole versions available for later insertion of cables or wires
• PVC material Available in Black Colour.

Split Flexible Conduits

• Material: PP(BLACK)
• All sizes in mm unless otherwise stated.
• ID or OD can vary ± 0.4 mm
• Manufactured from P.P. (Black)
• Used to protect wiring inside the wall to replace normal PVC pipe. Flexible design for better wire running.

Supreme PG Gland IP68

• UL approved material NYLON 66, 94V-2.
• Well designed for insulation, waterproof and impact resistant. Used extensively for protection and fixation of cables in control panel and apparatus.
• Mount body to pre-drilled panel hole and fix it with locking nut.
• Insert cables through body and then seals consequently. Finally, Press them together with press nut to hold cable in position.

Supreme-Metric Gland IP68

• UL approved Material Nylon 66, 94V-2.
• Suit a variety of applications, and diverse industries.
• Mount gland to pre-drilled panel hole, use locknut to fix gland on board, insert the cables in the seal, and then tighten up
• the nut to hold cables in position.
• Simply and quickly fixed, high degree of the protection IP68 preventing dust and water.

Rigid Shrinkable PVC Material.

Used for colour distinction and insulation of busbar in control panel. To be shrinked by blower or hot water.

Maximum service temp: 80

Available in Red white Blue and Black, 100mtr Roll.

A economical way of cable binding. Easily applied to electric harness cables and wire bundles. Cut-to-fit versality in convenient roll-form. Made from PE material or NYLON6. Excellent in insulation and binding strength. Flexible construction enable bands to follow wire ways easily. Durable, reusable with retained spiral strength. Fix ends of band with BANDEX cable ties and spiral wire bundles in clockwise direction to complete works.

Expand spiral range almost without limit.

Available in white colour, 10mtr Roll.

Earth Rod Coupler & Clamp

EARTH ROD COUPLER & CLAMP – 16 & 20mm

Solid Copper Earth Rods

Solid Copper Earth Rods are made from pure EC Copper (Natural Finish)

Solid Copper Earth Rods

Solid Copper Earth Rods are made from pure EC Copper (Natural Finish)

TUBULAR CABLE LUGS

• For Copper conductors
• Material: E-copper-BS 1977
• Surface: Tin Plated
• (With or without inspection hole)

CABLE LUGS BI METAL

Guaranteed particulars for bi metal cable lugs suitable for 1.1kv 87 above for R. core xlpe aluminium lt/ht cable

Raw material:

• Aluminium 99.50% (purity, min), conductivity 60% (min) of iacs in annealed condition.
• Copper 99.80% (purity, min), conductivity – 97% of iacs (min) of hot forged quality.
• Jointing method high speed friction welding
• Finish – natural (Fully annealed including joint)

E1W Gland for SWA cable

• Suitable for single wire armoured, plastic or rubber sheathed, extruded bedded cables
• Outer seal grips sheath of cable
• Inner seal grips bedding layer of cable
• For use in most climatic conditions weatherproof and waterproof
• Inner and outer seal rated to IP 66
• Design has separate armour locking ring
• Gland rated to IP66 with use of suitable washer or thread sealant at gland interface
• Finish: Natural Brass and also available in Electro Tinned and Nickel

Cable Gland – A1 A2

A1 A2 Type brass indoor cable gland is used with all types of unarmoured cable, providing mechanical cable retention. Sealing is provided on the cable outer sheath. A1 A2 range of industrial cable gland is designed and tested as per BS 6121:Part 1:1989. It meets the requirements of EN 50262:1999.

TECHNICAL SPECIFICATION

• Type – A1 A2
• Design Specification – BS 6121: Part 1: 1989
• Ingress Protection Rating – IP66
• Standard Gland Material – Brass
• Optional Gland Material – Nickel Plated Brass
• Cable Type – Unarmoured
• Sealing Area(s) – Cable Outer Sheath
• Available Accessories – Steel/Brass Locknut, PVC/LSF Shroud, Brass Earth Tag, Nylon Washer, Brass Reducer

Cable Glands – CW Brass

KEDBROOKE CW Type brass indoor and outdoor cable gland is used with all types of Single Wire Armour (SWA) cable providing mechanical cable retention and electrical continuity through armour wire termination. The clamping ring allows the cable to be easily disconnect from the equipment, for maintenance etc. This feature also provides remote make off procedures when the termination is to be conducted in areas of restricted access. This cable gland is designed and tested as per BS 6121:Part 1:1989. It meets the requirement of EN 50262:1999.

TECHNICAL SPECIFICATION

• Type – CW
• Design Specification – BS 6121: Part 1: 1989
• Ingress Protection Rating – IP66
• Standard Gland Material – Brass
• Optional Gland Material – Nickel Plated Brass
• Cable Type – Single Wire Armour (SWA)
• Sealing Area(s) – Cable Outer Sheath
• Available Accessories – Steel/Brass Locknut, PVC/LSF Shroud, Brass Earth Tag, Nylon Washer, Brass Reducer

Cable Glands – BW Brass

KEDBROOKE BW Type brass indoor cable gland is used with all types of Single Wire Armour (SWA) cable providing mechanical cable retention and electrical continuity through armour wire termination. The BW design offers the benefit of a longer body to protect the armour wires from impact. This cable gland is designed and tested to BS6121:1989. It meets the requirement of EN 50262:1999.

TECHNICAL SPECIFICATION

• Type – BW 4 Part
• Design Specification – BS 6121: Part 1: 1989
• Standard Gland Material – Brass
• Optional Gland Material – Nickel Plated Brass
• Cable Type – Single Wire Armour (SWA)
• Armour Clamping – Clamping Ring
• Available Accessories – Steel/Brass Locknut, PVC/LSF Shroud Brass Earth Tag, Nylon Washer, Brass Reducer

CAT- 6 Cable

Product Features & Technical Specifications

• Provides 250MHz standard
• Conductor Resistance at 20°C Ω/100m – max: 9.5
• Resistance percentage – max:3.0
• Near-end crosstalk dB/ lO0m min
• Meet EIA/TIA 568 B.2, EN 50173-1, ISO/IEC 11801 Standards.
• PVC jacket with HDPE insulation.
• Solid wire 24(AWG) Bare copper conductor and also available in 23(AWG)
• Operating temperature: -20°C to + 75°C
• Return Loss (Min. at 250MHz): 17.3 dB
• Attenuation: (Min. at 250 MHz) : 30.5 dB

Benefits

• Improved signal strength
• Better speed & performance
• Supports Gigabit Ethernet

PVC Flexible Cables

• Rated Voltage – 300/500v
• Conductor – Plain Annealed High Conductivity Flexible Copper As Per Class 5 Of IEC 60228
• Insulation Material – PVC
• Specification Standard – AS PER B6500

Rubber Cables

H07RN-F is a rubber flexible power cable specifically designed to operate in tough weather conditions and under high mechanical and thermal stresses. The hard-wearing H07RN-F cable is made up of class 5 flexible plain copper conductors, EPR (Ethylene Propylene Rubber) insulation and a black CPE sheath. With its oil, grease and water-resistant sheath, H07RN-F cable is suitable for use in a whole range of different applications, including handling equipment, mobile power supplies and stage and audio equipment.

Used as an internal connector in controllers, motor starters and rectifier equipment. It is designed for installation in switch control, metering, relay and instrumentation panels. It can be used in everything from automation and process control, building and construction to marine and defense, and transmission, distribution and power networks.

APPLICABLE STANDARDS

Alfanar cables are designed and tested to meet or exceed the requirements of BS 6231.However, alfanar can also supply a range of alternative designs to meet customer-specified requirements.

Technical Specifications:

• Conductor: Plain annealed flexible copper conductor class 5 as per BS EN 60228 and IEC 60228

Insulation

• Type BK: Extruded layer of Polyvinyl chloride (PVC) insulation Type TII with temperature rating70 °C at normal operation as per BS EN 50363-3
• Type СК: Extruded layer of Polyvinyl chloride (PVC) insulation Type TI3 with temperature rating90 °C at normal operation as per BS EN 50363-3
• Type CK: Extruded layer of Polyvinyl chloride (PVC) insulation with temperature rating 105 °C at normal operation available on request

Colors

• Standard colors are available in black, white, red, blue, green, yellow, yellow/green, pink, violet, orange, brown and gray.

Flame retardancy

• The cables have been tested and approved with the flame performance standards IEC 60332-1-2 and BS EN 60332-1.

We offer an extensive range of 0.6/1.0kV single-core and multi-core power and control cables. These cables have indoor and outdoor applications in power and petrochemical plants, utility buildings, electrical equipment, and more. We use the highest quality raw materials and the latest manufacturing techniques to produce these cables.

Multi Core

PVC/XLPE Insulated, Multi Core Cables, Steel Tape

Technical Specifications:

• Available with Copper or Aluminium conductors.
• Designed and tested in accordance with the latest IEC or BS standards.
• Available in Single-core (up to 1000 mm2) or Multi-core (up to 500 mm2) constructions.
• Available with Cross-linked Polyethylene (XLPE) or Polyvinyl Chloride (PVC) insulation.
• Provided with flame retardant PVC jacket to pass flame propagation test to IEC 60332-1.
• Available in Armoured/Non-armoured and Shielded/non-shielded constructions.
• Customized designs are available upon request.

Afanar offers a wide range of electrical building wires with thermoplastic PVC insulation for general purpose applications such as for supplying power and lighting in residential and commercial buildings. They are intended for use in the indoor fixed installation, distribution in conduits as well as in closed installation ducts, and is ideal for the internal wiring of appliances and apparatus.

Stranded wires

450/750V, PVC insulated (British standard)

• Designed and tested in accordance with the latest UL, BS or IEC standards.
• Designed with Max. Conductor Temperature at normal operation of 70 °C – 90 °C – 105 °C.
• Manufactured from electrolytic grade 99.97% pure copper.
• Manufactured with a superior grade flame retardant PVC insulation to IEC 60332- 1.
• Gasoline and oil resistant.
• Available with full range of colours and different packing options.

• A1/A2 Gland for unarmoured cable

• A2 flameproof for unarmoured cable

• BW gland for SWA cable

• CW gland for SWA cable

• CW flameproof gland for SWA cable

• E1W gland for SWA cable

• E1W flameproof gland for SWA cable

• G-Type gland for SWA cable

• U-Type gland for SWA cable

Cable Clips (Round)

• High Density PE material, Masonry steel nail.

• Applied for general round cables.

• Applied for telephone cords with nails inserted.

Made of finest soft grade, strong, durable PCV that will resist oil, grease, acid abrasion and chemicals.

BM CABLE MARKER features high quality flexible interior to fit various cable diameters. The markers stay attached on a roller and can be despatched easily when needed. Bold print on yellow body to show the codes precisely. Any numbers can be composed by arranging letters and numbers in sequence to provide the necessary codes. To be fitted before the terminal is attached or solder connection made and grip cable firmly in position.

GM CABLE MARKER with its unique oval shape design provide slip over cable directly (for small cable) slip onto marker strip (for larger cable or cable bundles)

MARKER STRIPS NYLON66 PLATE with cable tie fastening hole to accommodate marker pieces for easy identification of cable runs.

Cable Tie

• The cable ties ensure a secure hold of the items to be wrapped, thanks to the teeth on the belt and the self-locking system.

• It used to bundle wires, cables, wrapping and get gardening neat and tidy.

• You can enter manually or with a tool

• The end of the tape is slightly bent for insertion allows practical.

• UL approved Nylon 66, 94V-2, With good tensile strength and insulation, not easy to get aging.

• Standard colour is natural, black and white.

• Various sizes are available from 100mm to 1168mm.

• Designed and manufactured in accordance with IEC 60502 for low-voltage power cables.

• Copper or Aluminium conductor, Class 2 stranded (compacted or non-compacted) as per IEC 60228; Aluminium wire armouring used for single-core cables.

• Insulation: XLPE rated for 90°C continuous operation or PVC Type A, compliant with IEC 60502-1.

• Single-core or multi-core (2, 3, 4, or 5 cores and above) with circular or shaped conductors.

Armouring:

• Galvanized steel wire armour (SWA) for multi-core cables

• Aluminium wire armour (AWA) for single-core cables

• Double steel tape armour available as per IEC 60502

SPECIFICATIONS

• 450/750 Volts

• PVC Insulated Wires

• BS 6004, IEC 60227 and BS 6231

• HO 7V – U With Solid Conductor – TYPE 60227 IEC 01

APPLICATIONS

• Internal electrical wiring for homes, offices, and highrise buildings

• Distribution of low-voltage power for lighting circuits

• Power supply to socket outlets and general power points

PVC FLEXIBLE CABLE

• These cables are useful for use in dry or damp locations for medium duties in domestic premises, kitchens and offices

• Suitable for washing machines, refrigerators etc

• Can be used for cooking and heating appliances provided that the cable does not come in contact with the hot parts

• Voltage grade 300/500 V R.M.S.

SINGLE CORE CABLES

• These cables are used for the purpose of lighting in residential and commercial building in surface mounted or embedded conduits.

• Suitable for earth DC when fixed installation inside appliances, switch gear and control gear

• Voltage grade 300/500 V up to 1.0 mm2, 450/750 V for 1.5 mm2 & above.

CONTROL CABLES

• Multi-Core Control Cables with PVC and XLPE Insulation

• Copper Solid, Round stranded and Flexible Conductors

• Armoured /Un armoured/Copper Wire/Copper Tape/Lead Sheathed designs

• Color Coded with and without Green/Yellow Combination

• Fire Retardant Grades, Low Smoke and Zero Halogen Cables

• ESMA and BASEC certified products.

WIRES

• 300/500 Volts, 450/750 Volts, 600/1000 Volts PVC Insulated Wires

• Low Smoke and Zero Halogen Wires for electrical wiring in homes, apartments, commercial and industrial buildings

• Panel wires as per BS EN 50525, IEC 60227 and BS 6231 with Solid, Rigid and Flexible Conductors.

LOW VOLTAGE CABLES

• Low Voltage Cables with PVC and XLPE Insulation

• Copper/Aluminum Conductors

• Armoured/Un-armoured/Lead Sheathed designs

• Single Core and Multi-core Constructions

• Fire Retardant Grades, Low Smoke and Zero Halogen Cables

• ESMA and BASEC certified products

MEDIUM VOLTAGE CABLES

• Medium Voltage Cables with XLPE and TR-XLPE Insulation

• Copper/Aluminum Conductors

• Metallic Screen of Copper Tape/Copper Wire/Lead Sheath

• Armoured/Un-armoured designs

• Single Core and 3 Core Constructions

• Fire Retardant Grades

• PVC/LLDPE/MDPE/HDPE Sheathed and Low Smoke and Zero Halogen Cables

• ESMA and BASEC certified products.

Fire Resistant Cables for Fire Alarm Systems, Emergency Lighting & Voice Evacuation Syst

Certified by LPCB
ESMA Approved
Approved by Civil Defense of Dubai, Sharjah & Abu Dhabi
Approved by Bahrain Civil Defense
Approved by Royal Oman Police (ROP)

RAMCRO cables are used for Fire Resistant & Circuit Integrity and essential to prevent life from smoke and noxious fumes,
and where sensitive equipment may be damaged by acid forming gases.

Ramcro Fire resistant cables are with sub –branded Ramfirecro, are manufactured to meet the requirements in accordance
with the major international standards. ie, BS 7629/BS 6387, CWZ/IEC 60331-21/ EN50200 PH120/BS 8434-2/ etc.

Ramcro Fire Resistant Cable Range

Fire Planet – BS 6387 CWZ, Multi-core, Solid CU, Silicon Rubber – Insulation, Collective screen, LSZH – Sheath
Fire Sun – BS 7629, Multi-core, Solid/Stranded CU, Silicon Rubber – Insulation, Collective screen, LSZH – Sheath
Fire Star – Enhanced BS 8434-2 Multi-core Solid / Stranded CU, Mica+ XLPE + Silicon Rubber – Insulation, Collective screen,
LSZH – Sheath